There is no doubt that water filters are exposed to many problems and malfunctions, which you can avoid if you use the filter correctly and perform regular maintenance on it. To avoid malfunctions, you must install it according to the user and installation manual of the company that manufactured it. However, there are many people who do not know what are the causes of water filter malfunctions, and this is what will be explained in the following lines.
Causes of water filter failure
The reasons for water filter failure are as follows:
1. Not adhering to the regular water change schedule.
One of the causes of water filter failure is when you notice a change in the taste of the water resulting from the filtration process, i.e. it has become worse or has an unbearable odor, and this happens in a noticeable manner, then the cause is the second-stage, third-stage, fifth-stage filters, or all of them.
Here, you must replace the damaged filter. In addition, you must adhere to the schedule for changing it periodically to avoid any problems.
2. Problem with the electrical connections connected to the pump
The pump is the specialized part for pumping and transporting water to all parts of the filter so that the water produced by the filtering process reaches the individual.
If the filter pump is faulty and not working, the problem lies with the pump's electrical connections. That is, the entire electrical circuit, from the outlet to the transformer, to the pressure sensors, and finally to the motor itself. Therefore, you must inspect it carefully, and if you do not find any fault with it, then the fault lies with the transformer itself.
3. The filter pump is always running.
One of the reasons for a water filter failure is that the pump is constantly running. This can result in a failure in the pressure sensor located at the inlet of the first-stage pipe. There may also be a failure in the four-way valve, or a failure in the pump itself. In this case, you must repair or replace it if necessary.
4. Pipes not connected to each other
When a water leak occurs, it is because the pipes are not connected tightly to each other.
Here you must determine the location of the leak, and then tighten the pipe connections tightly.
You should keep in mind that the leak is likely caused by the pump itself, and if this happens, you will need to replace it.
5. No water reaching the faucet
There are several reasons why water won't reach the faucet, including the filter's internal water valve being closed. You should make sure it's open before taking any action.
There is a blockage in one of the filtration stages. Here, you must check all stages. This is done by unscrewing the candle of the second stage to ensure that the water is passing through the first stage. Until all stages are completed, and you have been able to reach the problem, you must then replace the filter of the blocked stage.
The four-way valve is clogged, which is caused by sediment in the filter. You must clean it regularly.
If you have followed all the previous steps and have not found the problem, disassemble the filter and have it checked by a specialist, as it may need to be replaced due to its expiration date.
Reasons for weak filter water
When water becomes scarce, this makes many people worry. Therefore, we will learn about the reasons for the weakness of filter water:
- Not paying attention to changing the candles in the water filter, as this results in blockage of the candles contained in the filter, and this is due to the presence of dirt, impurities, and the like, or there may be a large object stuck to it
- Another reason is to replace the spark plug with a conventional one, so you should get an original spark plug from the company.
The filter does not release water
When you encounter a problem where the filter is not draining water, you must change the filter candle on time and do not neglect this matter.
When you don't change it, bacteria and liquids accumulate on the candle and then reach the water tank, resulting in a change in the taste of the water.
The water filter motor does not shut down. What is the reason?
One of the problems people face is that the filter motor does not shut off. This is due to a rise in temperature, which you can confirm by placing your hand on the filter.
The reason for this is a blockage in the membranes, i.e. the water treatment, and the other reason is a fault in the GAC stage and the CTO stage not delivering water or a fault in the filter pump.
Water filter tank not filling
If you have a filter but it is not filling up, one of the reasons for this is low water pressure.
To address this issue, you need to increase the air pressure inside the tank. You can do this by using a hand pump or by connecting an air compressor to the water supply valve.
The filter motor is not working.
First, you need to make sure that the socket, plug, and electrical connections are all in the correct places. Here, you need to follow the following:
You disconnect the transistor from the socket and measure the output with an ohmmeter. If the transistor is working properly, then the problem may lie with the pressure sensor, whether it is low or high.
What causes water leakage from the water filter?
The problem is that the pump is unable to separate the water, so we have two options here, and this is after you turn off the water so that the water does not continue to flow onto the ground.
Therefore, you should repair the filter yourself if the problem is obvious and the leak is present. This can be done by connecting it or by contacting a technician who specializes in this matter.
How do I know if the filter motor is working?
Disconnect the clips until you are sure the copper is fully connected.
How do you know if the membranes are broken?
If the water comes out in weak drops, and the filter water is generally weak, you will find that the water tap is dripping.
Here the member has expired and you need to change it.
Home water filter parts
It was represented in:
- Electric pump: It pumps water.
- Product tank: It is responsible for collecting filtered water.
- Filters: Consists of 4, 5 or 6 stages.
- Filter inlet, water outlet, and drain outlet
Pure filter problems
- Pressure retention failure inside the tube
- Four-wheel drive fault
- Pump failure
Now that we've discussed the causes of water filter failure, remember that the expiration of the candle may result in health risks. Furthermore, some people purchase filters from untrusted companies, which can cause frequent filter failures and other similar issues.
English 
Arabic 
French 
Spanish 
Portuguese