Electric blenders are becoming increasingly prone to malfunctions, due to a number of reasons, including a burnt cord, a problem with the buttons, leaking liquids that can cause them to malfunction, motor problems, or grinding blade problems, among other issues. Below, we'll explore the causes of electric blender malfunctions and how to repair them.
Causes of electric mixer malfunctions and how to repair them
We can divide the solutions to problems that occur in blenders based on the damaged part. The following are the causes of electric blender malfunctions and ways to repair them:
1. The blender light is off and the blender cannot be turned on.
It is considered one of the most common causes of electric mixer malfunctions, and here it can be fixed in several points.
When you find that the light of the blender connected to the air outlet is off, this indicates that no electricity is reaching the blender. Here, you should try another outlet in the kitchen. In the event that no electricity is reaching the blender after you change the outlet, here there is a possibility that there is a burnt wire in it, and this is a result of the increased load on the blender. Here, follow the following.
Remove the mixer base and open it from the bottom to access the wire that connects between the motor and the speed control panel. Then, use a digital multimeter or even a continuity tester to check the wire. If the reading indicates that the circuit is open, this indicates that the wire is damaged.
You need to remove the damaged wire and connect a new one in the same place. You need to choose the same electrical capacity for the new wire as the old one.
2. The blender light is on and indicates that the blender is powered, but the blender is not working.
Here you need to make sure that there is a malfunction in the following parts, and it is possible that there are objects stuck inside the blender part from the inside, and this matter causes no electrical current to reach the motor and also to the parts that are responsible for operation. Here you can remove them by turning off the blender and then opening the bottom part to make sure that these parts are present and then get rid of them immediately.
The problem is likely with the power buttons that prevent the internal components from being activated. The problem is that they can't be clicked as usual. You can fix this problem by opening the blender base to access the button panel, which is now secured to the base with screws.
Additionally, you should ensure that all electrical circuit terminals are properly connected. You may need to use sprays or similar methods to dry out the moisture from the electrical components, or replace the button panel if the previous steps are unsuccessful.
3. Sudden stop of the blender while it is running
This problem is caused by a high temperature in the motor. The blender contains a heat-sensitive wire that shuts down the motor when the temperature reaches a certain level, protecting it from permanent damage. The solution to this problem is described in the following lines.
Unplug the blender and wait 15 minutes for it to cool down and for the sensitive power cord to return to standby. Avoid adding large quantities of food or larger, hard foods, as this can cause the motor to overwork and overheat.
If the blender doesn't respond to all the above solutions, you should connect the leads of the digital multimeter to the leads of the electric motor using the ohm section. Then, turn the speed knob to a low speed and take the resistance reading. Then, turn the screw in the direction of the grinder blade, i.e. clockwise. If there is a change in resistance, this is the most obvious indication of a damaged motor.
4. Liquid leakage from the mixer
There are several reasons for fluid leakage, including: Loose screws securing the base of the grinding blade to the blender jug. You can solve this problem by tightening the screws from the bottom of the blender. There is likely a hole in the blender. You can confirm this by filling the jug with water, preferably away from the bottom, and start noticing the leaking areas. There may be damage to the parts surrounding the screws, and in this case, they must be replaced.
5. Burning smell coming from the blender
If this smell spreads, this is sufficient evidence of the presence of various problems with the blender parts, and the reason for this is one of the following cases.
Engine damage may be caused by vibration of the seals and fluid reaching them, or it may be caused by crushing large quantities of food such as ice cubes and the like.
The rotor blade may also be damaged due to leakage of fluids from the rotating part that moves the blade. This increases the load on the motor, leading to damage. You can easily replace it by unscrewing the existing screws and installing new blades.
One of the problems is the burning or scorching of the carbon brushes located at the bottom of the mixer.
How does an electric mixer work?
An electric blender is a kitchen appliance used to mix or puree food, juices, and the like. You can operate it by plugging its cord into an electrical outlet and then pressing the power button.
What are the components of a blender?
All electric mixers generally consist of two parts: the upper part, which consists of a container that houses a rotating knife, the purpose of which is to mash and chop the contents.
The lower part, which consists of the blender body, contains buttons to operate the electric blender, in addition to the electric motor, which rotates the container blade.
The blender knife does not rotate
When the blade in the blender stops turning, it means the material inside is too hard and too large, or it may be slow. You need to adjust it properly so that it rotates.
Sparks coming out of the engine
- Due to engine misalignment
- One of the reasons is that the engine valves are not adjusted properly.
- Disconnect the grounding cable of the motor.
The blender motor is on fire
If the motor starts to fire, this could be due to damage to the coils, or it could be due to some liquid falling on the bottom of the blender. In this case, you must disconnect it and have it examined by a technician specialized in this field.
mixer repair shop
Citizens are now looking for shops specializing in repairing mixtures. Some of these shops include the following:
- Mill Workshop
- Al-Suwailem Home Appliance Maintenance
- Al-Eisaei store
- Future Summit Store
- Al-Ameri store
There is no doubt that over time you will encounter one of the above problems with your blender. If this happens, you must identify the cause of the problem and fix it. Therefore, we previously mentioned the causes of electric blender malfunctions and ways to fix them.
English 
Arabic